PC Card Products
1
ATA30 Series
October 2001
ATA PCMCIA Card
ATA33 Series
FEATURES
·
PC Card ATA compatible
- 68 pin two piece connector and type I or type II housing
(5mm)
- PCMCIA/JEIDA 4.1
· x8/x16 PCMCIA standard interface
· Single 3 Volt / 5 Volt Supply
· ISA standard, Read/Write unit is 1 sector (512 bytes)
- Sector Read/Write transfer rate:
-sustain: approx 1MB/sec (ATA33)
- High reliability based on internal ECC function (Error
Correcting Code)
· Card Capacity
- 32 MB to 1024 MB (unformatted)
· Card Access mode:
- Memory card mode
- I/O card mode
- True-IDE mode
· Reliability:
· MTBF
1,000,000 hours
· Data reliability is 1 error in 10
14
bits read
· Auto Sleep Function
WEDC ATA33 Series flash memory cards are ATA
compatible cards and are suitable for usage as a data
storage memory medium for PC's or any other
electronic equipment. This product is built with high
performance NAND memory devices and SanDisk
controller.
Packaged in a PCMCIA type I or type II housing,
the WEDC ATA series cards provide a lightweight,
low power, reliable nonvolatile storage medium.
Built in to the card controller, Error Correcting Code
(ECC) provides a high level of reliability and MTBF
(Mean Time Between Failures).
WEDC's standard cards are shipped with the WEDC
FLASH Logo. Cards are also available with blank
housings (no Logo). The blank housings are available
in both a recessed (for label) and flat housing. Please
contact your WEDC sales representative for further
information on Custom artwork.
NOTE: ATA33 product family is electrically and
functionally compatible with the older ATA30.
ATA Flash card
ATA PCMCIA Card
Block Diagram
W
HITE
E
LECTRONIC
D
ESIGNS
Host Interface
OSC
CONTROLLER
...
Memory Array
DATA I/O
CONTROL
Code/software
DATA
ADRS
FLASH Memory
PC Card Products
4
ATA30 Series
October 2001
ATA PCMCIA Card
ATA33 Series
Start up time / System Performance
Sleep to Write
2.5ms max
Sleep to Ready
2.0 ms max
Reset to Ready
50 ms typ, 400 ms max
Data trasfer rate to/from Flash
4.0MB/sec burst
Data trasfer rate to/from Host
6.0MB/sec burst
Active to Sleep Delay
Programable
Controller overhead Command to DRQ <1.25 ms
Power requirements (Note 1)
DC input voltage
Commercial
3.3V ±5%, 5V ±10%
Industrial
3.3V ±5%, 5V ±5%
Typ power Dissipation (Note 3, 4)
Sleep
200uA (3.3V), 500uA (5V)
Read
32-50mA (3.3V), 46-90mA (5V)
Write
32-70mA (3.3V), 46-110mA (5V)
Environmental Spec.
Temperature
Operating Commercial
0 to 60 C
Operating Industrial
-40 to 85 C
Non-operating Commercial
-25 to 85 C
Humidity
200uA (3.3V), 500uA (5V)
Operating
8 - 95% non-condensing
Non-operating
8 - 95% non-condensing
Vibration
Operating
15G peak to peak max
Non-operating
15G peak to peak max
Shock
Operating
1000 G max
Non-operating
1000 G max
Reliability
MTBF
1,000,000 hours
Notes:
1.
All values are typical at ambient temperature and nominal supply voltage, unless
otherwise stated
2.
All performance timing asuumes the controller is in the default (I.e. faster) mode
3.
Sleep mode currently is specified under the condition that all card inputs are in static
CMOS levels and in a "Not Busy" operating state.
4.
The current specified, shows the bounds of programmability of the product