- 268 -
SF1004G-Q1
10.0 AMPS. Glass Passivated Super Fast Rectifiers
Voltage Range
200 Volts
Current
10.0 Amperes
Features
Low forward voltage drop
High current capability
High reliability
High surge current capability
Mechanical Data
Case: Molded plastic
Epoxy: UL 94V-O rate flame retardant
Terminals: Leads solderable per MIL-STD-
202, Method 208 guaranteed
Polarity: As marked
High temperature soldering guaranteed:
260
o
C/10 seconds .16",(4.06mm) from
case.
Weight: 2.24 grams
TO-220
Dimensions in inches and (millimeters)
Maximum Ratings and Electrical Characteristics
Rating at 25
ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Type Number
Symbol
SF1004G-Q1
Units
Maximum Recurrent Peak Reverse Voltage
V
RRM
200 V
Maximum RMS Voltage
V
RMS
140 V
Maximum DC Blocking Voltage
V
DC
200 V
Maximum Average Forward Rectified Current
.375 (9.5mm) Lead Length @T
C
= 100
I
(AV)
10.0 A
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated Load
(JEDEC method )
I
FSM
125 A
Maximum Instantaneous Forward Voltage
@ 5.0A
@10.0A
V
F
1.1
1.25
V
Maximum DC Reverse Current @ T
A
=25
at Rated DC Blocking Voltage @ T
A
=100
I
R
10.0
500
uA
uA
Reverse Recovery Charge(Per Diode)
@IF=2A, VR
30V
,
-dIF/dt=20A/uS
QS
9 NC
Thermal Resistance Junction to Case (Note 3)
R
JC
3.0
/W
Rating for Fusing (t < 8.3mS)
I
2
t
65 A
2
S
Maximum Reverse Recovery Time (Note 1)
Trr
25 nS
Typical Junction Capacitance (Note 2)
Cj
10 pF
Operating Temperature Range
T
J
-50 to +150
Storage Temperature Range
T
STG
-50 to +150
Notes: 1. Reverse Recovery Test Conditions: I
F
=0.5A, I
R
=1.0A, I
RR
=0.25A
2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C.
3. Thermal Resistance from Junction to Case Mounted on Heatsink. Size of 2 in x 3 in
x 0.25 in, Al-Plate.
PIN 1
PIN 3
Positive CT
PIN 2
CASE
- 269 -
RATINGS AND CHARACTERISTIC CURVES (SF1004G-Q1)
FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50
W
NONINDUCTIVE
1W
NON
INDUCTIVE
OSCILLOSCOPE
(NOTE 1)
PULSE
GENERATOR
(NOTE 2)
DUT
(+)
50Vdc
(approx)
(-)
NOTES: 1. Rise Time=7ns max. Input Impedance=
1 megohm 22pf
2. Rise Time=10ns max. Sourse Impedance=
50 ohms
(-)
(+)
10
W
NONINDUCTIVE
-1.0A
-0.25A
0
+0.5A
trr
1cm
SET TIME BASE FOR
5/ 10ns/ cm
FIG.2- MAXIMUM FORWARD CURRENT DERATING
CURVE
A
VERAGE
FOR
W
ARD
CURRENT
.
(A)
0
50
100
150
0
2
4
6
8
10
CASE TEMPERATURE. ( C)
o
FIG.3- TYPICAL REVERSE CHARACTERISTICS
INST
ANT
ANEOUS
REVERSE
CURRENT
.(
A
)
0
20
40
60
80
100
120
140
1000
0.1
1
10
100
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
TJ=25 C
0
TJ=100 C
0
FIG.4- MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT
PEAK
FOR
W
ARD
SURGE
CURRENT
.
(A)
1
2
5
10
20
100
50
150
120
90
60
30
0
NUMBER OF CYCLES AT 60Hz
TJ=125 C
0
8.3ms Single Half Sine Wave
JEDEC Method
FIG.5- TYPICAL JUNCTION CAPACITANCE
CAP
ACIT
ANCE.(pF)
1
5
2
10
20
50
100
200
500
50
60
70
80
90
100
REVERSE VOLTAGE. (V)
Tj=25 C
0
FIG.6- TYPICAL FORWARD CHARACTERISTICS
INST
ANT
ANEOUS
FOR
W
ARD
CURRENT
.
(A)
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
0.01
0.1
0.03
1
0.3
10
3
30
100
FORWARD VOLTAGE. (V)
Tj=25 C
Pulse Width=300 s
1% Duty Cycle
o
40
1000
PDF 
ZIP