1
INDUSTRIAL TEMPERATURE RANGE
IDTQSIDTQS32XL384
HIGH-SPEED CMOS 20-BIT BUS SWITCH
APRIL 2002
2002 Integrated Device Technology, Inc.
DSC-5732/3
c
INDUSTRIAL TEMPERATURE RANGE
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
APPLICATIONS:
· Hot-swapping, hot-docking
· Voltage translation (5V to 3.3V)
· Logic replacement (data processing)
· Power conservation
· Capacitance reduction and isolation
· Low power for hand held and mobile applications
· Bus isolation
· Clock gating
FEATURES:
· Enhanced N channel FET with no inherent diode to V
CC
· 5
bidirectional switches connect inputs to outputs
· Zero propagation delay, zero ground bounce
· Undershoot Clamp Diodes on all switch and control Inputs
· Four enables control five bits each
· TTL-compatible input and output levels
· Available in 48-pin QVSOP package
IDTQS32XL384
QUICKSWITCH
®
PRODUCTS
HIGH-SPEED CMOS
20-BIT BUS SWITCH
DESCRIPTION:
The QS32XL384 provides a set of twenty high-speed CMOS TTL-
compatible bus switches. The low ON resistance of the QS32XL384 allows
inputs to be connected to outputs without adding propagation delay and
without generating additional ground bounce noise. The Bus Enable (BE)
signals turn the switches on. Four Bus Enable signals are provided, one
for each of five bits of the 20-bit bus. The `384 family of QuickSwitch products
is ideal for switching wide digital buses, as well as hot-docking, 5V to 3V
conversion and capacitance isolation for power conservation.
The QS32XL384 is characterized for operation at -40°C to +85°C.
B
4
BEC
BEA
B
0
A
4
A
0
B
9
B
5
A
9
A
5
B
14
BEB
BED
B
10
A
14
A
10
B
19
B
15
A
19
A
15
FUNCTIONAL BLOCK DIAGRAM
2
INDUSTRIAL TEMPERATURE RANGE
IDTQS32XL384
HIGH-SPEED CMOS 20-BIT BUS SWITCH
PIN CONFIGURATION
Symbol
Description
Max
Unit
V
TERM
(2)
SupplyVoltage to Ground
0.5 to +7
V
V
TERM
(3)
DC Switch Voltage V
S
0.5 to +7
V
V
TERM
(3)
DC Input Voltage V
IN
0.5 to +7
V
V
AC
AC Input Voltage (pulse width
20ns)
3
V
I
OUT
DC Output Current
120
mA
P
MAX
Maximum Power Dissipation (T
A
= 85°C)
0.5
W
T
STG
Storage Temperature
65 to +150
°C
ABSOLUTE MAXIMUM RATINGS
(1)
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
2. V
CC
terminals.
3. All terminals except V
CC
.
Pins
Typ.
Max.
(1)
Unit
Control Inputs
3
5
pF
Quickswitch Channels (Switch OFF)
5
7
pF
CAPACITANCE
(T
A
= +25°C, F = 1MHz, V
IN
= 0V, V
OUT
= 0V)
NOTE:
1. This parameter is guaranteed but not production tested.
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
Z = High-Impedence
BEA
BEB
B
0
- B
4
B
15
- B
19
Function
H
H
Z
Z
Disconnect
L
H
A
0
- A
4
Z
Connect
H
L
Z
A
15
- A
19
Connect
L
L
A
0
- A
4
A
15
- A
19
Connect
BEC
BED
B
5
- B
9
B
10
- B
14
Function
H
H
Z
Z
Disconnect
L
H
A
5
- A
9
Z
Connect
H
L
Z
A
10
- A
14
Connect
L
L
A
5
- A
9
A
10
- A
14
Connect
FUNCTION TABLE
(1)
QVSOP
TOP VIEW
Pin Names
I/O
Description
A
0
- A
19
I/O
Bus A
B
0
- B
19
I/O
Bus B
BEA
I
Enable,
0 - 4
BEB
I
Enable,
15 - 19
BEC
I
Enable,
5 - 9
BED
I
Enable,
10 - 14
PIN DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
BEA
B
0
A
0
A
1
B
1
B
2
A
2
A
3
B
3
B
4
A
4
GND
BEC
B
5
A
5
A
6
B
6
B
7
A
7
A
8
B
8
B
9
A
9
GND
V
CC
B
19
A
19
A
18
B
18
B
17
A
17
A
16
B
16
B
15
A
15
BEB
V
CC
B
14
A
14
A
13
B
13
B
12
A
12
A
11
B
11
B
10
A
10
BED
3
INDUSTRIAL TEMPERATURE RANGE
IDTQSIDTQS32XL384
HIGH-SPEED CMOS 20-BIT BUS SWITCH
R
ON
(ohms)
V
IN
(Volts)
Symbol
Parameter
Test Conditions
Min.
Typ.
(1)
Max.
Unit
V
IH
Input HIGH Voltage
Guaranteed Logic HIGH for Control Pins
2
--
--
V
V
IL
Input LOW Voltage
Guaranteed Logic LOW for Control Pins
--
--
0.8
V
I
IN
Input Leakage Current (Control Inputs)
0V
V
IN
V
CC
--
±0.01
±1
µA
I
OZ
Off-State Current (Hi-Z)
0V
V
OUT
V
CC
, Switches OFF
--
±0.01
±1
µA
R
ON
Switch ON Resistance
V
CC
= Min., V
IN
= 0V, I
ON
= 30mA
--
5
7
V
CC
= Min., V
IN
= 2.4V, I
ON
= 15mA
--
10
15
V
P
Pass Voltage
(2)
V
IN
= V
CC
= 5V, I
OUT
= -5µA
3.7
4
4.2
V
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Industrial: T
A
= 40°C to +85°C, V
CC
= 5.0V ± 5%
NOTES:
1. Typical values are at V
CC
= 5.0V and T
A
= 25°C.
2. Pass voltage is guaranteed but not production tested.
TYPICAL ON RESISTANCE vs V
IN
AT V
CC
= 5V
16
14
12
10
8
6
4
2
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4
INDUSTRIAL TEMPERATURE RANGE
IDTQS32XL384
HIGH-SPEED CMOS 20-BIT BUS SWITCH
NOTES:
1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics.
2. Per TTL driven input (V
IN
= 3.4V, control inputs only). A and B pins do not contribute to
Icc.
3. This current applies to the control inputs only and represents the current required to switch internal capacitance at the specified frequency. The A and B inputs generate no significant
AC or DC currents as they transition. This parameter is guaranteed but not production tested.
POWER SUPPLY CHARACTERISTICS
Symbol
Parameter
Test Conditions
(1)
Max.
Unit
I
CCQ
Quiescent Power Supply Current
V
CC
= Max., V
IN
= GND or V
CC
, f = 0
6
µA
I
CC
Power Supply Current
per Input HIGH
(2)
V
CC
= Max., V
IN
= 3.4V, f = 0
2.5
mA
I
CCD
Dynamic Power Supply Current per MHz
(3)
V
CC
= Max., A and B Pins Open
0.25
mA/MHz
Control Input Toggling @ 50% Duty Cycle
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
T
A
= -40°C to +85°C
Symbol
Parameter
Min.
(1)
Typ.
Max.
Unit
t
PLH
Data Propagation Delay
(2,4)
0.25
(3)
ns
t
PHL
Ax to Bx, Bx to Ax
t
PZL
Switch Turn-On Delay
1.5
6.5
ns
t
PZH
BE to Ax, Bx
t
PLZ
Switch Turn-Off Delay
(2)
1.5
5.5
ns
t
PHZ
BE to Ax, Bx
NOTES:
1. Minimums are guaranteed but not production tested.
2. This parameter is guaranteed but not production tested.
3. The time constant for the switch alone is of the order of 0.25ns at C
L
= 50pF.
4. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. Since this time constant is much smaller
than the rise and fall times of typical driving signals, it adds very little propagation delay to the system. Propagation delay of the bus switch, when used in a system, is determined
by the driving circuit on the driving side of the switch and its interaction with the load on the driven side.
5
INDUSTRIAL TEMPERATURE RANGE
IDTQSIDTQS32XL384
HIGH-SPEED CMOS 20-BIT BUS SWITCH
ORDERING INFORMATION
CORPORATE HEADQUARTERS
for SALES:
for Tech Support:
2975 Stender Way
800-345-7015 or 408-727-6116
logichelp@idt.com
Santa Clara, CA 95054
fax: 408-492-8674
(408) 654-6459
www.idt.com
4/22/2002 Page 2, changed pins 34 and 35
DATA SHEET DOCUMENT HISTORY
IDTQS
XXXXX
XX
Package
Device Type
Blank
Industrial (-40°C to +85°C)
48-Pin QVSOP
QVSOP - Green
Q1
Q1G
32XL384
High Speed 20-Bit Bus Switch
X
Process
PDF 
ZIP