GBPC1005 THRU GBPC110
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
Reverse Voltage - 50 to 1000 Volts Forward Current - 3.0 Amperes
FEATURES
Plastic package has Underwriters Laboratory Flammability
Classification 94V-0
This series is UL listed under Recognized Component Index,
file number E54214
Glass passivated chip junctions
High case dielectric with standing voltage of 1500 V
RMS
Typical I
R
less than 0.1
µ
A
High surge current capability
Ideal for printed circuit boards
High temperature soldering guaranteed:
260°C/10 seconds, 0.375" (9.5mm) lead length,
5lbs. (2.3kg) tension
MECHANICAL DATA
Case: Molded plastic body over passivated junctions
Terminals: Plated leads solderable per MIL-STD-750,
Method 2026
Mounting Position: Any
(NOTE 1)
Mounting Torque: 5.0 in. - lb. max.
Weight: 0.1 ounce, 2.8 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
GBPC
GBPC
GBPC
GBPC
GBPC
GBPC
GBPC
SYMBOLS 1005
101
102
104
106
108
110
UNITS
Maximum repetitive peak reverse voltage
V
RRM
50
100
200
400
600
800
1000
Volts
Maximum RMS bridge input voltage
V
RMS
35
70
140
280
420
560
700
Volts
Maximum DC blocking voltage
V
DC
50
100
200
400
600
800
1000
Volts
Maximum average forward
T
C
=60°C
(NOTE 2)
3.0
rectified output current at
T
A
=25°C
(NOTE 3)
I
(AV)
2.0
Amps
Peak forward surge current single sine-wave
superimposed on rated load (JEDEC Method) T
C
=60°C
I
FSM
60.0
Amps
Rating for fusing (t<8.3ms)
I
2
t
15.0
A
2
sec
Maximum instantaneous forward voltage drop
per leg at 1.5 Amperes
V
F
1.0
Volts
Maximum DC reverse current at rated
T
A
= 25°C
5.0
DC blocking voltage per leg
T
A
=125°C
I
R
500.0
µ
A
Typical junction capacitance per leg
(NOTE 4)
C
J
21.0
pF
Typical thermal resistance per leg
(NOTE 2)
R
JA
12.0
R
JC
8.0
°C/W
Operating junction and storage temperature range
T
J,
T
STG
-55 to +150
°C
NOTES:
(1) Bolt down on heat-sink with silicone thermal compound between bridge and mounting surface for maximum heat transfer with #6 screw
(2) Unit mounted on 4.0 x 4.0 x 0.11" thick (10.5 x 10.5 x 0.3cm) Al. Plate
(3) Unit mounted on P.C.B. at 0.375" (9.5mm) lead length with 0.5 x 0.5" (12 x 12mm) copper pads
(4) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
HOLE FOR
#6 SCREW
0.158 (4.01)
0.142 (3.61)
DIA.
0.128 (3.25)
0.048 (1.22)
0.200 (5.08)
0.160 (4.06)
0.750
(19.05)
MIN.
0.040 (1.02) TYP.
0.094 (2.4) x 45 degrees
0.445 (11.30)
0.405 (10.29)
0.630 (16.00)
0.590 (14.98)
AC
AC
Polarity shown on side of case: Positive lead by beveled corner
0.445 (11.30)
0.405 (10.29)
0.630 (16.00)
0.590 (14.98)
0.032 (0.81)
0.028 (0.71)
DIA.
Case Style GBPC1
Dimensions in inches and (millimeters)
4/98
0
50
100
150
0
1.0
2.0
3.0
4.0
5.0
0.1
1.0
10
100
1
10
100
0.01
0.1
1
10
100
0.1
1
10
100
1
10
100
0
10
20
30
40
50
60
0.4
0.6
0.8
1.0
1.2
1.4
1.6
0.01
0.1
1
10
20
0
20
40
60
80
0.01
0.1
1
10
50
100
RATINGS AND CHARACTERISTICS CURVES GBPC1005 THRU GBPC110
FIG. 1 - DERATING CURVE OUTPUT RECTIFIED
CURRENT
AMBIENT TEMPERATURE, °C
AMBIENT TEMPERATURE, T
A
P.C.B. MOUNTING
0.375" (9.5mm) LEAD LENGTH
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
INSTANTANEOUS REVERSE CURRENT,
MICROAMPERES
T
J
=25°C
PULSE WIDTH=300
µ
s
1% DUTY CYCLE
FIG. 3 - TYPICAL FORWARD CHARACTERISTICS
PER LEG
INSTANTANEOUS FORWARD CURRENT,
AMPERES
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
PER LEG
REVERSE VOLTAGE, VOLTS
T
J
=25
°
C
f=1.0 MHz
Vsig=50mVp-p
T
J
=25°C
CASE TEMPERATURE,
T
C
HEAT-SINK
MOUNTING,
4.0 x 4.0 x 0.11" THK
(10.5 x 10.5 x 0.3cm)
AL. PLATE
60 H
Z
RESISTIVE OR
INDUCTIVE LOAD
AVERAGE FORWARD OUTPUT
CURRENT, AMPERES
FIG. 4 - TYPICAL REVERSE LEAKAGE
CHARACTERISTICS PER LEG
NUMBER OF CYCLES AT 60 H
Z
PEAK FORWARD SURGE CURRENT,
AMPERES
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT PER LEG
T
J
=125°C
FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE
PER LEG
TRANSIENT
THERMAL IMPEDANCE,
°C/W
t, HEATING TIME, sec.
T
C
=60°C
SINGLE SINE-WAVE
(JEDEC METHOD)
1.0 CYCLE
JUNCTION
CAPACITANCE, pF
PDF 
ZIP