DS07-12405-3E
FUJITSU SEMICONDUCTOR
DATA SHEET
8-bit Proprietary Microcontroller
CMOS
F
2
MC-8L MB89160/160A Series
MB89161/163/165/P165/PV160/W165
MB89161A/163A/165A
s
DESCRIPTION
The MB89160 series is a line of the general-purpose, single-chip microcontrollers. In addition to a compact
instruction set, the microcontrollers contain a variety of peripheral functions such as an LCD controller/driver,
an A/D converter, timers, a serial interface, PWM timers, and external interrupts.
s
FEATURES
· F
2
MC-8L family CPU core
· Dual-clock control system
· Maximum memory size: 16-Kbyte ROM, 512-byte RAM (max.)
· Minimum execution time: 0.95
µ
s/4.2 MHz
· I/O ports: max. 54 channels
· 21-bit time-base counter
· 8/16-bit timer/counter: 2 or 1 channels
· 8-bit serial I/O: 1 channel
· External interrupts (wake-up function): Four channels with edge selection plus eight level-interrupt channels
· 8-bit A/D converter: 8 channels
· 8-bit PWM timers: 2 channels
· Watch prescaler (15 bits)
· LCD controller/driver: 24 segments
×
4 commons (max. 96 pixels)
· LCD driving reference voltage generator and booster (option)
· Remote control transmission output
· Buzzer output
· Power-on reset function (option)
· Low-power consumption modes (stop, sleep, and watch mode)
· CMOS technology
2
MB89160/160A Series
s
PACKAGE
(FTP-80P-M05)
(FPT-80C-A02)
(MQP-80C-P01)
80-pin Ceramic MQFP
80-pin Plastic SQFP
80-pin Ceramic QFP
(FTP-80P-M06)
(FTP-80P-M11)
80-pin Plastic QFP
80-pin Plastic QFP
3
MB89160/160A Series
s
PRODUCT LINEUP
(Continued)
MB89161/
MB89161A
*1
MB89163/
MB89163A
*1
MB89165/
MB89165A
*1
MB89P165
MB89W165
MB89PV160
Classification
Mass production products
(mask ROM products)
One-time
PROM
product
EPROM
product
Piggyback/
evaluation
product (for
development)
ROM size
4 K
×
8 bits
(internal
mask ROM)
8 K
×
8 bits
(internal mask
ROM)
16 K
×
8 bits
(internal
mask ROM)
16 K
×
8 bits
(internal PROM, programming
with general-purpose EPROM
programmer)
32 K
×
8 bits
(external
ROM)
RAM size
128
×
8 bits
256
×
8 bits
512
×
8 bits
CPU functions
Number of instructions:
136
Instruction bit length:
8 bits
Instruction length:
1 to 3 bytes
Data bit length:
1, 8,16 bits
Minimum execution time:
0.95
µ
s/4.2 MHz
Interrupt processing time:
9
µ
s/4.2 MHz
Ports
I/O port (N-ch open-drain):
8 (6 ports also serve as peripherals, 3 ports
are a heavy-current drive type.)
Output ports (N-ch open-drain):
28 (16 ports also serve as segment pins, 2 ports
serve as booster capacitor connection pins,
2 ports serve as common pins.)
*3
(8 ports also serve as an A/D input)
I/O ports (CMOS):
16 (12 ports also serve as an external interrupt)
Output ports (CMOS):
2 (Also serve as peripherals)
Total:
54 (max.)
Timer/counter
8-bit timer operation (toggled output capable, operating clock cycle 1.9
µ
s to 486
µ
s)
16-bit timer operation (toggled output capable, operating clock cycle 1.9
µ
s to 486
µ
s)
Serial I/O
8 bits
LSB first/MSB first selectability
One clock selectable from four operation clocks
(one external shift clock, three internal shift clocks: 1.9
µ
s, 7.6
µ
s, 30.4
µ
s)
LCD controller/
driver
Common output:
4 (max.)
Segment output:
24 (max.)
*3
Bias power supply pins:
4
LCD display RAM size:
24
×
4 bits
Booster for LCD driving:
Built-in (product with a booster)
*3
Dividing resistor for LCD driving: Built-in (an external resistor
selectability)
Without a
booster for
LCD driving
A/D converter
8-bit resolution
×
8 channels
A/D conversion mode (conversion time 43
µ
s/4.2 MHz (44 instruction cycles))
Sense mode (conversion time 11.9
µ
s/4.2 MHz)
Continuous activation by an internal timer capable
Reference voltage input
Part number
Parameter
4
MB89160/160A Series
(Continued)
*1: Products with an internal booster.
*2: Varies with conditions such as the operating frequency. (The operating voltage of the A/D converter is assured
separately. See section "
s
Electrical Characteristics.")
*3: See section "
s
Mask Options."
s
PACKAGE AND CORRESPONDING PRODUCTS
: Available
×
: Not available
Note: For more information about each package, see section "
s
Package Dimensions."
MB89161/
MB89161A
*1
MB89163/
MB89163A
*1
MB89165/
MB89165A
*1
MB89P165
MB89W165
MB89PV160
PWM timer 1,
PWM timer 2
8 bits
×
2 channels
8-bit reload timer operation (toggled output capable, operating clock cycle: 0.95
µ
s to
124 ms)
8-bit resolution PWM operation (conversion cycle: 243
µ
s to 32 s)
External interrupt 1
(wake-up function)
4 independent channels (edge selectability)
Rising edge/falling edge selectability
Used also for wake-up from stop/sleep mode.
(Edge detection is also permitted in stop mode.)
External interrupt 2
"L" level interrupts
×
8 channels
Buzzer output
1 (7 frequencies are selectable by the software.)
Remote control
transmission
output
1 (Pulse width and cycle are software selectable.)
Standby modes
Subclock mode, sleep mode, stop mode, and watch mode
Process CMOS
Operating voltage
*2
2.2 V to 6.0 V (single clock)/
2.2 V to 4.0 V (dual clock)
2.7 V to 6.0 V
EPROM for use
--
MBM27C256A-
20TV
Package
MB89161
MB89161A
MB89163
MB89163A
MB89165
MB89165A
MB89PW165
MB89W165
MB89PV160
FPT-80P-M05
×
×
FPT-80P-M06
×
×
FPT-80P-M11
×
×
MQP-80C-P01
×
×
×
×
×
FPT-80C-A02
×
×
×
×
×
Part number
Parameter
5
MB89160/160A Series
s
DIFFERENCES AMONG PRODUCTS
1. Memory Size
Before evaluating using the piggyback product, verify its differences from the product that will actually be used.
Take particular care on the following points:
· On the MB89161/A and MB89163/A, the upper half of each register bank cannot be used.
· The stack area, etc., is set at the upper limit of the RAM.
2. Current Consumption
· In the case of the MB89PV160, add the current consumed by the EPROM which is connected to the top socket.
· When operated at low speed, the product with an OTPROM (one-time PROM) or an EPROM will consume
more current than the product with a mask ROM.
However, the current consumption in the sleep/stop modes is the same. (For more information, see section
"
s
Electrical Characteristics.")
3. Mask Options
Functions that can be selected as options and how to designate these options vary by the product.
Before using options check section "
s
Mask Options."
Take particular care on the following points:
· A pull-up resistor cannot be set for P20 to P27 on the MB89P165.
· A pull-up resistor is not selectable for P40 to P47 and P60 to P67 if they are used as LCD pins.
· Options are fixed on the MB89PV160.
PDF 
ZIP