1 of 5
111999
FEATURES
Automatically restarts a microprocessor after
power failure
Maintains reset for 150 ms after V
CC
returns
to an in-tolerance condition
Reduces need for discrete components
Precision temperature-compensated voltage
reference and voltage sensor
Low-cost TO-92 or space saving surface
mount SOT-23 packages available
Push-Pull output for low current operation
Operating temperature -40°C to +85°C
PIN ASSIGNMENT
PIN DESCRIPTION
TO-92
1
RST
Active Low Reset Output
2 V
CC
Power
Supply
3 GND Ground
SOT-23
1
RST
Active Low Reset Output
2 V
CC
Power
Supply
3 GND Ground
DESCRIPTION
The DS1810 EconoReset uses a precision temperature reference and comparator circuit to monitor the
status of the power supply (V
CC
). When an out-of-tolerance condition is detected, an internal power-fail
signal is generated which forces reset to the active state. When V
CC
returns to an in-tolerance condition,
the reset signal is kept in the active state for approximately 150 ms to allow the power supply and
processor to stabilize.
DS1810
5V EconoReset with Push-Pull Output
www.dalsemi.com
1
2
3
SOT-23 PACKAGE
1 2 3
1 2 3
TO-92 PACKAGE
See Mech.
Drawings Section
DS1810
2 of 5
OPERATION - POWER MONITOR
The DS1810 provides the function of detecting out-of-tolerance power supply conditions and warning a
processor-based system of impending power failure. When V
CC
is detected as out-of-tolerance, the
RST
signal is asserted. On power-up,
RST
is kept active for approximately 150 ms after the power supply has
reached the selected tolerance. This allows the power supply and microprocessor to stabilize before
RST
is released.
BLOCK DIAGRAM (PUSH-PULL OUTPUT) Figure 1
APPLICATION EXAMPLE Figure 2
OUTPUT VALID CONDITIONS
All versions of the DS1810 can maintain a valid output as long as V
CC
remains above 1.2 volt. However,
the
RST
outputs on the DS1810 use a push-pull structure which can maintain a valid output below 1.2
volts on an input. To sink current below 1.2 volts, a resistor can be connected from
RST
to Ground (see
Figure 3). This arrangement will maintain a valid value on the
RST
outputs even it V
CC
approaches 0
volts. During both power-up and -down this arrangement will draw current when
RST
is in the high state.
A value of about 100 k should be adequate to maintain a valid condition.
DS1810
3 of 5
APPLICATION DIAGRAM:
RST
VALID TO 0 VOLTS VCC ON THE DS1810 Figure 3
TIMING DIAGRAM: POWER-UP Figure 4
TIMING DIAGRAM: POWER-DOWN Figure 5
DS1810
4 of 5
ABSOLUTE MAXIMUM RATINGS*
Voltage on V
CC
Pin Relative to Ground
-0.5V to +7.0V
Voltage on
RST
Relative to Ground
-0.5V to V
CC
+0.5V
Operating Temperature
-40°C to +85°C
Storage Temperature
-55°C to +125°C
Soldering Temperature
260°C for 10 seconds
*
This is a stress rating only and functional operation of the device at these or any other conditions
above those indicated in the operation sections of this specification is not implied. Exposure to
absolute maximum rating conditions for extended periods of time may affect reliability.
RECOMMENDED DC OPERATING CONDITIONS (-40
°
C to +85
°
C)
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS NOTES
Supply Voltage
V
CC
1.2
5.5
V
1
DC ELECTRICAL CHARACTERISTICS (-40
°
C to +85
°
C; V
CC
=1.2V to 5.5V)
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS NOTES
Output Voltage @ 0-500
µ
A
V
OH
V
CC
-0.5V V
CC
-0.1V
V
1
Output Current @ 2.4V
I
OH
350
µ
A
2
Output Current @ 0.4V
I
OL
+10
mA
2
Operating Current V
CC
< 5.5
I
CC
30
40
µ
A
3
V
CC
Trip Point (DS1810-5)
V
CCTP
4.50
4.62
4.75
V
1
V
CC
Trip Point (DS1810-10)
V
CCTP
4.25
4.37
4.49
V
1
V
CC
Trip Point (DS1810-15)
V
CCTP
4.00
4.12
4.24
V
1
Output Capacitance
C
OUT
10
pF
AC ELECTRICAL CHARACTERISTICS (-40
°
C to +85
°
C; V
CC
=1.2V to 5.5V)
PARAMETER
SYMBOL
MIN
TYP
MAX
UNITS NOTES
RESET Active Time
t
RST
100
150
300
ms
V
CC
Detect to
RST
t
RPD
2
5
µ
s
V
CC
Slew Rate
(V
CCTP
(MAX) to V
CCTP
(MIN))
t
F
300
µ
s
V
CC
Slew Rate
(V
CCTP
(MIN) to V
CCTP
(MAX))
t
R
0
ns
V
CC
Detect to
RST
t
RPU
100
150
300
ms
4
DS1810
5 of 5
NOTES:
1.
All voltages are referenced to ground.
2.
Measured with V
CC
2.7 volts.
3.
Measured with
RST
output open.
4.
t
R
= 5
µ
s.
PART MARKING CODES
"A", "B", &"C" represent the device type.
810
-
DS1810
811 -
DS1811
812 -
DS1812
813 -
DS1813
815 -
DS1815
816 -
DS1816
817 -
DS1817
818 -
DS1818
"D" represents the device tolerance.
A -
5%
B -
10%
C -
15%
D -
20%
SOT-23 PACKAGE
PDF 
ZIP